Make sure you have the correct shears for the technique you are using, either copper foil or lead.You should be able to see the black felt pen line between each shape. Once you’ve cut them all, check their accuracy by placing them on the tracing paper.You can rub candle wax on the blades to prevent the thin strips sticking. Break it off every inch or so to stop this happening. Do it slowly, especially around corners, as the strip can get caught up. Simply place them so that the line is in between the two outside blades.Ĭut around each pattern piece. Luckily, the copper foil and lead shears are designed to cut the correct amount of card away from your pattern.This means that you have to cut all the glass pieces a tiny bit smaller to make room for the foil and solder or heart of the lead. Why? Because either the width of the copper foil and solder, or the heart of the stained glass lead came will fill the gap when you assemble the panel. The next step is to cut a thin strip of card out between each shape. ![]() Cut neatly around the edge of the whole design with regular scissors. You are going to cut the stained glass templates from this. How To Cut The Stained Glass Templates Pieces This line represents the gap which the heart of the lead will fill later on.ģ. This will be used for assembling your panel when you’re ready.ĭo the same as above, only this time with the 1/16″ (2mm) thicker pen. On the tracing paper, go over all the lines – except the outside lines – with the fine pen. Put aside the carbon paper and your stained glass pattern.This makes it easier when I’m trying to find how they fit together after they’re all cut.Īt this stage you should have your pattern drawn on the tracing paper and the thin card. It’s very important to number the shapes now, when all the pieces are together.You want to make sure that the pattern reads clearly on the thin card at the bottom. With the pencil, draw over the pattern with a constant, firm pressure.Laying down order for making cutting pattern 2. It’s very important that nothing moves at this stage. The tracing paper goes on top of the pile. Then the carbon paper (face down), followed by your pattern. Pattern shears for copper foil.*įor lead came construction: A 1/16 (2mm) black felt tip pen. Scissors.įor copper foil construction: Fine felt tip pen. If any of the pieces don’t fit, making the final picture will be difficult. The following steps are all easy but it’s worth taking a bit of time doing them accurately. Thanks in advance but no worries if you have a local store – I’d always support them first □ ) How to Cut Stained Glass Templates Just so’s you know, if you click and buy through the link within 24 hrs I get a small % from Amazon, (not you!). (This article contains some affiliate links – look for the *. You can cut stained glass templates most accurately with Foil Shears* or Lead Shears*, depending on which construction technique you’re using. These will be used as templates for cutting all your glass pieces. Once you’ve designed or found a stained glass pattern that you’re happy with, the next thing you need to do is make copies of it and cut the individual shapes out accurately. Please Note - Price is for the 3D printed parts only.Accurate stained glass templates are crucial for creating beautiful panels. However, please note that it has to be a thin walled part to leave some space for you to add color and therefore may be damaged if not handled carefully. We try to make the pattern as robust as possible by using high quality PLA material and through careful design. Please note sizes are approximate as there is some shrinkage when the part is removed from the printer. 11.25 inches square and 1/16" thick giving plenty of depth for your pour. It will also fin on a 12 inch square panel with a small clearance around the outside edge. 11.25 inches square so that it will fit into a 12 inch square frame. It is intended that the pattern remain a permanent part of the finished piece combining your favorite method with the crisp lines and symmetry of the 3D printed part. The artist can then pour colored resin into the different areas creating beautiful personalized intricate stained glass effect artwork. ![]() This 3D printed part sits flat against a glass sheet or transparent acrylic panel allowing the artist to stick it in place using a thin coat of resin. ![]() One time use Stained Glass Pattern for use in resin art.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |